Browse all practice questions for the Get Wired 102 Introduction to the Basic Installation of Lighting Fixtures and Branch Circuits Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Get Wired 102 Introduction to the Basic Installation of Lighting Fixtures and Branch Circuits Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • If two resistors have equal value and are connected in parallel, the total resistance is half of one resistor.
  • If a ballast PF is 0.94, what percentage of the apparent power is real power?
  • A two-branch parallel circuit has 2A of current in one branch and 3A in the other branch. Which branch is considered to have the larger load?
  • In circuit analysis, replacing a parallel block with a single resistor is described as using which form?
  • A series circuit has a total resistance of 180 Ohms and an applied voltage of 120V. What is the current flow?
  • A two-branch parallel circuit has a 30 ohm and a 15 ohm resistor. What is the total resistance?
  • Is it permissible to install a Type Non-IC recessed luminaire directly against wood ceiling joists?
  • A junction point of current paths is often called a __.
  • A circuit that has only one path for current flow is a ___ circuit?
  • An old nongrounded non-GFCI bathroom receptacle must be replaced with what type?
  • A method for finding total resistance of parallel resistors is ___.
  • In a series circuit, the voltage across each resistor adds up to the applied voltage.
  • What does AFCI stand for?
  • In a three-resistor series circuit with an applied voltage of 180 V, the voltage across the first resistor is 50 V and the second resistor is 125 V. The voltage across the third resistor is ___.
  • In a series circuit, which statement about current is true?
  • What is the function of a Metal Oxide Varistor (MOV) in electrical protection?
  • A frequent step in solving combination circuits is which of the following?
  • On a standard grounding-type receptacle, what color are the grounded terminals?
  • Two identical resistors of 40 Ω each are connected in parallel. What is the total resistance?
  • When solving for both parallel and series circuits the rules stay the same when finding which quantity?
  • Feed-through GFCI receptacles allow 20 amp wiring to 15 amp devices downstream.
  • A connection of three (or more) current paths is often called a _____?
  • In a series circuit with two resistors, 10 Ω and 12 Ω, and 5 A flowing through each resistor, what is the total current in the circuit?
  • The meaning of approved is ___.
  • A method for finding total resistance of parallel resistors is which of the following?
  • What is the special shape and color of the grounding terminals on receptacle outlets and other devices?
  • GFCI protection generally covers ___ in garages.
  • In solving a combination circuit, it is necessary to simplify a parallel block to which form?
  • What happens if the line and load connections of an older style feed-through GFCI receptacle are reversed?
  • What is the best method to answer a code question in the NEC?
  • To identify which paths are series and which paths are parallel, you should which of the following?
  • Which scenario describes proper use of a multi-wire branch circuit with safety?
  • In a series circuit, which quantity is the same at any point along the circuit?
  • Circuits that have more than one path for current flow are ___ circuits.
  • In a parallel circuit consisting of a 12 V source and two resistors, 6 Ω and 12 Ω, which branch carries more current?
  • In a parallel circuit, the amount of current flow in a branch is known as the ___ of the branch.
  • Which location is not required to be GFCI protected?
  • A recessed luminaire bears no marking indicating it is 'Identified for Through-Wiring'. Is it permitted to run branch-circuit conductors other than the conductors that supply the luminaire through the integral junction box?
  • Transients are ___.
  • The exception to the GFCI requirement in a garage includes
  • In a multi-wire branch circuit, which safety requirement is correct?
  • In a parallel circuit, the total resistance is ___ value resistance.
  • In a parallel circuit, the applied voltage across each branch is equal to what?
  • Which statement best describes the requirement when selecting fluorescent lighting for a luminaire?
  • Which area is included when calculating the usable area of a dwelling to compute the required lighting load?
  • Is it a Code requirement to install GFCI receptacles in a fully carpeted, finished recreation room in the basement?
  • Which color is associated with the neutral terminal on most standard receptacles?
  • What color are the hot terminals on a standard grounding-type receptacle?
  • Which NEC article governs rigid polyvinyl conduit?
  • According to the NEC, systems with voltage over how many volts must be grounded?
  • A parallel circuit with a 10 Ω resistor and a 22 Ω resistor is connected to a 60 V supply. What is the current in the 10 Ω resistor?
  • NM-B is a nonmetallic cable used in branch circuits. Which statement best describes NM-B?
  • What does ampacity refer to?
  • A simple parallel circuit contains which of the following?
  • In a parallel circuit, the total current is the sum of the currents in each branch.
  • A series circuit has a total resistance of 240 Ohms and a current flow of 4 A. What is the applied voltage?
  • In a series circuit, if two resistors dissipate 6 W and 9 W and the total power is 25 W, how much does the third resistor dissipate?
  • Which feature distinguishes an electromagnet from a permanent magnet?
  • A three-branch parallel circuit has resistors of 27 Ω, 56 Ω, and 15 Ω. What is the total resistance?
  • In a parallel circuit, the total power equals which of the following?
  • What does the acronym GFCI stand for?
  • Arc fault protection is required for ___.
  • In a series circuit, which property remains constant along the path?
  • Which quantity across a resistor is proportional to its resistance?
  • Magnetic lines of force are referred to as what?
  • GFCI devices trip at a ground-fault current of at or above how many milliamperes?
  • The circled E on a ballast nameplate indicates that the ballast is a(n) _____.
  • Generally, voltages less than __ volts are considered safe from electrical shock hazards.
  • Which statement about trimming a recessed luminaire is correct?
  • In a surge protection context, what is the function of a Metal Oxide Varistor in an SPD?
  • A device that is designed to open and disconnect a circuit in the event of excessive current is a ___.
  • What term describes a flexible connection between an outlet box and a luminaire?
  • What material is used for the recreation room ceiling finish when installing surface-mounted fluorescent luminaires?
  • Feed through GFCI receptacles allow ___ downstream.
  • In a parallel circuit with a 150 Ω resistor and a 270 Ω resistor connected to a 120 V supply, what is the current through the 150 Ω resistor?
  • Which term describes a flexible connection between an outlet box and a luminaire?
  • In which NEC section is the voltage maximum for home lighting equipment referenced?
  • In a series circuit, the voltage across each component adds up to the ___.
  • What is the primary function of a GFCI device?
  • NEC 310.3(C) requires that conductors 8 AWG and larger must be ___ when installed in a raceway.
  • What characterization describes a simple parallel circuit?
  • In magnetic terminology, the term flux refers to which of the following?
  • In parallel circuits, the voltage drop across any branch is the same as the ___.
  • Small appliance receptacle outlets __ required to be included in the 3 volt-ampere per square foot load calculation.
  • A parallel circuit with 120 Ω and 220 Ω resistors has a 240 V supply. What is the total circuit current?
  • Is a receptacle required on a 3ft (914 mm) wall space behind a door that is normally left open?
  • What is the maximum open-circuit voltage for lighting equipment in or on homes?
  • A GFCI circuit breaker is ___ than a receptacle type.
  • Which device is designed to control fluorescent lighting loads?
  • A parallel circuit with a 62 kΩ resistor and an 82 kΩ resistor across 480 V. What is the power of the 82-kΩ resistor?
  • Connectors marked CO-ALR are suitable for use with aluminum, copper, or copper-clad conductors. Conductors not marked are for copper conductors only.
  • May a GFCI receptacle be installed as a replacement in an old installation where the two-wire circuit has no equipment grounding conductor?
  • What current through a female human being will cause muscle contractions that will keep her from letting go of the live wire?
  • Dirty power is generally defined as having which characteristic?
  • _____ receptacles can be used as replacements for two-wire (ungrounded) receptacles.
  • The ballast rating of 85 VA measures which quantity?
  • What does a PF of 0.94 imply about the proportion of real power to apparent power?
  • A combination circuit is a circuit that contains __.
  • A parallel circuit is formed with two resistors of 60 ohms each. What is the total resistance of the circuit?
  • In parallel circuits, the voltage drop across any branch is the same as the __.
  • The suffix "B" in Type NM-B nonmetallic cable means that the conductors have an insulation temperature rated ____.
  • Which area in a dwelling is not required to have AFCI protection for its branch-circuit outlets?
  • Factory-installed Thermal Protection in recessed incandescent luminaires is intended to prevent overheating.
  • A ballast rated for two 40-W lamps draws 80 W of real power. If its apparent power is 85 VA, what is the ballast power factor?
  • The let-go current is the point at which muscle contractions will prevent release.
  • GFCIs are set to trip between milliamps.
  • What is the approximate total resistance of a parallel circuit containing 15 Ω, 30 Ω, and 60 Ω resistors?
  • Transients on a power line can cause spikes or surges of energy that can damage delicate electronic components. What device is designed to mitigate this risk?
  • In a series circuit, the current through all components is the same.
  • A magnet that produces a magnetic field as a result of current flow in a conductor is called a(n) electromagnet.
  • The rating of 85 VA on a ballast refers to which electrical quantity?
  • For a parallel circuit, the sum of the powers in each branch represents which quantity?
  • These ballasts contain internal ___ protection to protect against overheating.
  • Unless specifically designated, all recessed incandescent luminaires must be provided with factory-installed _____.
  • A dual-rated conductor marked THHN/THWN is rated ____ when used in dry locations.
  • Rigid polyvinyl conduit is permitted to do all of the following, except for.
  • In a series circuit, which statement describes the relationship between the voltages across the resistors and the applied voltage?
  • A three-resistor circuit has a total power of 25 W. Two of the resistors dissipate 10 W and 5 W respectively. How much power does the third resistor dissipate?
  • The number of conductors permitted in rigid metal conduit is specified in ___.
  • SPD protection is necessary where?
  • In a series circuit with two resistors, the total resistance is equal to the ___ of the two resistors?
  • Resistors which have only one ohmic value are called _____ resistors.
  • In a series circuit, the current is the same through all components.
  • Which statement explains why you might redraw a circuit during combination analysis?
  • In a series circuit, the ___ is the sum of the individual resistances.
  • When installing a Type Non-IC fixture, insulation shall not be installed within how many inches of the side of the recessed luminaire?
  • Can an incandescent lamp dimmer be used to control a fluorescent lamp load?
  • Which statement correctly describes a Surge Protection Device's role in protecting electronics in a surge event?
  • Rigid polyvinyl conduit is an example of which category of conduit?
  • In a surge protection device, the energy of a transient is absorbed by which component?
  • To retrofit a two-wire ( ungrounded) receptacle for safety, what upgrade is commonly recommended?
  • The two resistors in a series circuit have voltages of 25 V and 60 V. The applied voltage is?
  • In an old installation without equipment grounding, can a GFCI receptacle be used as a replacement for a defective outlet?
  • What two types of receptacles may be used to replace a defective receptacle in an older home wired with knob-and-tube wiring that has no equipment grounding means in the box?
  • Fluorescent ballasts for all indoor applications must be type ___.
  • Which equation correctly relates voltage, current, and resistance in Ohm's law?
  • In NEC terminology, a conductor other than a service conductor that has overcurrent protection ahead of its point of supply that exceeds the value permitted for similar conductors is called a ___.
  • A 30-ohm resistor is connected to a 4-volt supply. How many watts will this resistor dissipate?
  • Which exception to the GFCI requirement in garages is described as listed locking support and mounting receptacles used with compatible attachment fittings installed for serving a ceiling luminaire?
  • What does the circled E on a ballast nameplate indicate?
  • When more resistors are added in parallel, what happens to the total resistance?
  • When installing single pole GFCI and AFCI circuit breakers in a panel, it is permissible to connect them to a multi-wire branch circuit.
  • If total resistance is 165 Ω and applied voltage is 120 V, the current is approximately ___ A.
  • The total current in a parallel circuit is equal to the sum of the currents through all the circuit branches.
  • Fluorescent ballasts are commonly rated in volt-amperes (VA). Which statement is true?
  • Identify the term for a flexible connector between an outlet box and a luminaire.
  • Which statement accurately reflects the relationship between lamp wattage, lamp type, and ballast in a luminaire?
  • True or False: The lamp type is irrelevant as long as the wattage matches the ballast.
  • In series circuits, the quantity that remains the same at every point in the circuit is the?
  • What is the unit of electrical power?
  • AFCI requirements for dwelling units are ___.
  • When selecting a trim for a recessed luminaire, which criterion is correct?
  • Which locations typically require GFCI protection for receptacles?
  • What leakage current range must trip an IDCI?
  • What does SPD stand for?
  • Surge protective devices are primarily used to protect equipment by which action?
  • What is the total wattage of two 40-W lamps?
  • Recessed luminaires that can be installed in direct contact with thermal insulation bear which Type mark?
  • In solving combination circuits, which action reduces the circuit to a simpler form?
  • The long slot on a 15-ampere, 125-volt, receptacle is the ____ conductor.
  • Who has the authority to determine code compliance in electrical installations?
  • A fluorescent ballast designed for two 40-watt lamps is rated at 85 VA. What is its power factor?
  • If a series circuit has resistor values of 27 ohms, 56 ohms, and 82 ohms, the total resistance is?
  • In residential garages, where must GFCI receptacles be installed?
  • The current in a parallel circuit splits among branches based on each branch's resistance; lower resistance draws more current.
  • Should you always match a fluorescent lamp's wattage and type designation to the ballast in the luminaire?
  • A parallel circuit is composed of two 60 Ohms resistors. What is the total resistance?
  • The term 'load' refers to the amount of _____ in a circuit branch.
  • Branch circuit conductors shall have an ampacity ___ than the maximum to be served.
  • Which device is designed to interrupt current and can be reset?
  • The installation of a surface-mounted fluorescent luminaire on a recreation room ceiling finished with low-density cellulose fiberboard would have what label on the luminaire?
  • A series circuit has two resistors. The resistors dissipate 10 W and 15 W. What is the total power dissipation of the circuit?
  • Construction sites must have receptacle outlets used for temporary wiring protected by which mechanism?
  • The 'let go' current for a person in contact with live wires refers to the point at which muscle contractions will keep a person from releasing the wire.
  • In a parallel circuit, the total current is equal to the ___ of the individual branch circuits.
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy